Refer to the exhibit. An engineer must configure HSRP for VLAN 1000 on SW2. The secondary switch must immediately take over the role of active router if the interlink with the primary switch fails. Which command set completes this task?

sw2(config)#track 1000 interface gigabitEthernet 0/0 line-protocol
sw2(config-track)# exit
sw2(config)# interface vlan 1000
sW2(confia-if)# ip address 10.23.87.3 255.255.255.0

A. 
sw2(config-if)# standby version 2
sw2(config-if)# standby 1000 ip 10.23.87.1
sw2(config-if)#standby 1000 priority 95
sw2(config-if)# standby 1000 track 1000

B. 
sw2(config-if)# standby 1000 ip 10.23.87.1
sw2(config-if)#standby 1000 priority 95
sw2(config-if)# standby 1000 preempt
sw2(config-if)# standby 1000 track 1000

C. 
sw2(config-if)# standby version 2
sw2(config-if)# standby 1000 ip 10.23.87.1
sw2(config-if)#standby 1000 priority 95
sw2(config-if)# standby 1000 preempt
sw2(config-if)# standby 1000 track 1000

D. 
sw2(config-if)# standby version 2
sw2(config-if)# standby 1000 ip 10.23.87.1
sw2(config-if)#standby 1000 priority 95
sw2(config-if)# standby 1000 preempt
sw2(config-if)# standby 1000 track gigabitEthernet 0/0

Refer to the exhibit. An engineer must configure HSRP for VLAN 1000 on SW2. The secondary switch must immediately take over the role of active router if the interlink with the primary switch fails. Which command set completes this task?

sw2(config)#track 1000 interface gigabitEthernet 0/0 line-protocol
sw2(config-track)# exit
sw2(config)# interface vlan 1000
sW2(confia-if)# ip address 10.23.87.3 255.255.255.0

A. 
sw2(config-if)# standby version 2
sw2(config-if)# standby 1000 ip 10.23.87.1
sw2(config-if)#standby 1000 priority 95
sw2(config-if)# standby 1000 track 1000

B. 
sw2(config-if)# standby 1000 ip 10.23.87.1
sw2(config-if)#standby 1000 priority 95
sw2(config-if)# standby 1000 preempt
sw2(config-if)# standby 1000 track 1000

C. 
sw2(config-if)# standby version 2
sw2(config-if)# standby 1000 ip 10.23.87.1
sw2(config-if)#standby 1000 priority 95
sw2(config-if)# standby 1000 preempt
sw2(config-if)# standby 1000 track 1000

D. 
sw2(config-if)# standby version 2
sw2(config-if)# standby 1000 ip 10.23.87.1
sw2(config-if)#standby 1000 priority 95
sw2(config-if)# standby 1000 preempt
sw2(config-if)# standby 1000 track gigabitEthernet 0/0

Correct Answer: C

HSRP v1 allow only 265 group numbers. HSRP v2 allow 4096 group number